Ultrasonic sensor UC1000-30GM-E6R2-K-V15
- Brand:Pepperl+Fuchs
- Product Code: UC1000-30GM-E6R2-K-V15
- Availability: Out Of Stock
Single head system, Parameterization interface for the application-specific adjustment of the sensor setting via the service program ULTRA 3000, 2 programmable switch outputs, Hysteresis mode selectable, Series: -30GM, Operating voltage: 10 ... 30 V DC , ripple 10 %SS, Interface type: RS 232, 9600 Bit/s , no parity, 8 data bits, 1 stop bit, Output type: 2 switch outputs PNP, NO/NC, programmable, UL approval: cULus Listed, General Purpose
Datasheet excerpt: Technical data of UC1000-30GM-E6R2-K-V15
| Product Description |
|---|
| Single head system |
| General specifications | ||
|---|---|---|
| Sensing range | 80 ... 1000 mm | |
| Adjustment range | 120 ... 1000 mm | |
| Dead band | 0 ... 80 mm | |
| Standard target plate | 100 mm x 100 mm | |
| Transducer frequency | approx. 180 kHz | |
| Response delay | 65 ms minimum 195 ms factory setting | |
| Indicators/operating means | ||
| LED green | solid: Power-on flashing: Standby mode or program function object detected | |
| LED yellow 1 | solid: switching state switch output 1 flashing: program function | |
| LED yellow 2 | solid: switching state switch output 2 flashing: program function | |
| LED red | solid: temperature/program plug not connected flashing: fault or program function object not detected | |
| Temperature/TEACH-IN connector | Temperature compensation , Switch points programming , output function setting | |
| Electrical specifications | ||
| Operating voltage | 10 ... 30 V DC , ripple 10 %SS | |
| No-load supply current | ≤ 50 mA | |
| Interface | ||
| Interface type | RS 232, 9600 Bit/s , no parity, 8 data bits, 1 stop bit | |
| Input/Output | ||
| Synchronization | bi-directional 0 level -UB...+1 V 1 level: +4 V...+UB input impedance: > 12 KOhm synchronization pulse: ≥ 100 µs, synchronization interpulse period: ≥ 2 ms | |
| Synchronization frequency | ||
| Common mode operation | max. 30 Hz | |
| Multiplex operation | ≤ 30 Hz / n , n = number of sensors , n ≤ 5 | |
| Output | ||
| Output type | 2 switch outputs PNP, NO/NC, programmable | |
| Rated operating current | 200 mA , short-circuit/overload protected | |
| Voltage drop | ≤ 2.5 V | |
| Repeat accuracy | ≤ 0.1 % of full-scale value | |
| Switching frequency | ≤ 2.5 Hz | |
| Range hysteresis | 1 % of the adjusted operating range (default settings), programmable | |
| Temperature influence | ≤ 2 % from full-scale value (with temperature compensation) ≤ 0.2 %/K (without temperature compensation) | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 | |
| Approvals and certificates | ||
| UL approval | cULus Listed, General Purpose | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Mechanical specifications | ||
| Connection type | Connector plug M12 x 1 , 5-pin | |
| Housing diameter | 30 mm | |
| Degree of protection | sensor head: IP67 connector sensor head/controller unit: IP52 | |
| Material | ||
| Housing | stainless steel (1.4305 / AISI 303) PBT plastic parts | |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam | |
| Mass | 210 g | |
| Factory settings | ||
| Output 1 | Switching point: 200 mm output function: Switch point operation mode output behavior: NO contact | |
| Output 2 | Switching point: 1000 mm output function: Switch point operation mode output behavior: NO contact | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27272803 |
| ECLASS 12.0 | 27272803 |
| ECLASS 11.0 | 27272803 |
| ECLASS 10.0.1 | 27272803 |
| ECLASS 9.0 | 27272803 |
| ECLASS 8.0 | 27272803 |
| ECLASS 5.1 | 27272803 |
| ETIM 9.0 | EC001849 |
| ETIM 8.0 | EC001849 |
| ETIM 7.0 | EC001849 |
| ETIM 6.0 | EC001849 |
| ETIM 5.0 | EC001849 |
| UNSPSC 12.1 | 41111960 |