Laser retroreflective sensor, small design, polarization filter, 21 m detection range, laser red light, light/dark on, push-pull output, test input, M12 plug, Series of sensors in a widely used standard housing, Visible red light, pulsed LASER light, Precision: high degree of repeatability thanks to small light spot, Objects can be reliably detected down to 0 mm: no blind zone, Resistant against noise: reliable operation under all conditions
| General specifications |
| Effective detection range | 0 ... 12 m |
| Reflector distance | 0 ... 12 m |
| Threshold detection range | 17 m |
| Reference target | MH82 reflector |
| Light source | laser diode |
| Light type | modulated visible red light |
| Polarization filter | yes |
| Laser nominal ratings | |
| Note | LASER LIGHT , DO NOT STARE INTO BEAM |
| Laser class | 1 |
| Wave length | 650 nm |
| Beam divergence | < 1.5 mrad |
| Pulse length | 1.8 µs |
| Repetition rate | 17.86 kHz |
| max. pulse energy | 6.7 nJ |
| Diameter of the light spot | approx. 5 mm x 12 mm at 15 m detection range |
| Opening angle | 0.02 ° |
| Ambient light limit | |
| Continuous light | 50000 Lux |
| Modulated light | 5000 Lux |
| Functional safety related parameters |
| MTTFd | 930 a |
| Mission Time (TM) | 10 a |
| Diagnostic Coverage (DC) | 90 % |
| Indicators/operating means |
| Operation indicator | LED green, flashes in case of short-circuit |
| Function indicator | 2 LEDs yellow, light up when light beam is free, flash when falling short of the stability control, off when light beam is interrupted |
| Control elements | rotary switch for light/dark, sensitivity adjuster |
| Electrical specifications |
| Operating voltage | 10 ... 30 V DC |
| Ripple | max. 10 % |
| No-load supply current | max. 40 mA |
| Input |
| Test input | emitter deactivation at 0 V |
| Output |
| Switching type | light/dark on switchable |
| Signal output | 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected |
| Switching voltage | max. 30 V DC |
| Switching current | max. 0.1 A |
| Voltage drop | ≤ 2.5 V DC |
| Switching frequency | 2500 Hz |
| Response time | 0.2 ms |
| Conformity |
| Product standard | EN 60947-5-2 |
| Laser safety | IEC 60825-1:2007 Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 |
| Compliance with standards and directives |
| Standard conformity | |
| Shock and impact resistance | IEC / EN 60068. half-sine, 40 g in each X, Y and Z directions |
| Vibration resistance | IEC / EN 60068-2-6. Sinus. 10 -150 Hz, 5 g in each X, Y and Z directions |
| Laser class | IEC 60825-1:2007 Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 |
| Approvals and certificates |
| EAC conformity | TR CU 020/2011 |
| Protection class | II, rated voltage ≤ 300 V AC with pollution degree 1-2 according to IEC 60664-1 |
| UL approval | cULus Listed, Type 1 enclosure |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Ambient conditions |
| Ambient temperature | -10 ... 50 °C (14 ... 122 °F) |
| Storage temperature | -20 ... 65 °C (-4 ... 149 °F) |
| Mechanical specifications |
| Housing width | 41.5 mm |
| Housing height | 49 mm |
| Housing depth | 15 mm |
| Degree of protection | IP67 |
| Connection | Metal connector, M12, 5-pin, 90° rotatable |
| Material | |
| Housing | Frame: nickel plated, die cast zinc,
Laterals: glass-fiber reinforced plastic PC |
| Optical face | Plastic pane |
| Mass | 60 g |
